![your name english dub with subtitles your name english dub with subtitles](http://obdtech.cn/uploadfiles/Product/20191126220033.jpg)
- #YOUR NAME ENGLISH DUB WITH SUBTITLES HOW TO#
- #YOUR NAME ENGLISH DUB WITH SUBTITLES SERIAL#
- #YOUR NAME ENGLISH DUB WITH SUBTITLES FULL#
- #YOUR NAME ENGLISH DUB WITH SUBTITLES CODE#
#YOUR NAME ENGLISH DUB WITH SUBTITLES FULL#
In case for to read and write memory devices you use other programmer, then after memory device is read and file is saved by your programmer you have to load this file in TMPro2 by clicking on Open file button.OBDSTAR X300 DP Plus C Package Full Version: Immobilizer+Mileage correction+Diagnosis+Special function (Oil rest +ABS+Battery matching+ECU programming+EPB+Throttle programming+Airbag rest+TPMS+Steering angle rest+OBDII+DPF+Injector code+Supension matching+Gear learning+CVT learning+EEPROM+Key renewing+ECU cloning)Adapter(P001 programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smarkt key Emulator)+others(Ignition coil+Remote tester) OBDSTAR X300 DP Plus 8 Inch Tablet Key Programmer Full Package After reading is done if you wish you can save file read for your archive.
![your name english dub with subtitles your name english dub with subtitles](https://ae01.alicdn.com/kf/H17f27bc15dc04290bf00e911c4da207bL/Immo-pin-code-calculation-service-For-Hyundai-KIA-Chrysler-Dodge-Jeep-GM-MG-GreatWall-Calculator-program.jpg)
You can buy it along with basic set or at later time.Īfter all connections are done, you have to press on Select and read memory device button, select correct memory device and press OK to process with reading. NOTE:Motorola HC805P18 adapter is not included in basic set of TMPro2. NOTE:Microchip PIC adapter, eeprom adapter, cable with 8 stripped wires and cable for adapters are included in basic set of TMPro2. To read or write these memory devices you have to use other programmer. To connect adapters to TMPro2 box you must use cable for adapters. Solder wires according to connection diagram for particular software. To read or write Microchip PIC you must use TMPro2 PIC adapter. Desolder MCU from immobox and solder it on adapter. * Motorola HC805P18. To read or write this Motorola you must use TMPro2 Motorola HC805P18 adapter. To read or write these MCU you have to use cable with 8 stripped wires. * Motorola 912/9S12 not locked, ST10F269 or Moric. On adapter there are sockets for 3 different types – DIL, SMD and SSOP.
#YOUR NAME ENGLISH DUB WITH SUBTITLES SERIAL#
Supported are all 93cXX, 24cXX, 25/95cXXX, X5328, S29190, X24c01, 95p08.To read or write serial eeproms, you must desolder it from board and solder on TMPro2 eeprom adapter. Memory device depends on unit, that contains key data. When type of memory device is clear, you have to see how you can read/write it.įor 70% of softwares reading and writing of memory devices can be done either by TMPro2 or by other programmer.įor 5% of softwares reading and writing is mandatory to be made with TMPro2.įor 25% of softwares for reading and writing of memory devices you must use other programmer. For some of units memory device is easy to be accessed, but for other it is not easy – you must cut a hole, dig a silicone etc. Remove unit from vehicle, open it and locate memory device.
![your name english dub with subtitles your name english dub with subtitles](http://www.key-programmer.com/wp-content/uploads/2015/12/chrysler-pin-code-reader-1.jpg)
Also you need to know which unit contains key data, and it`s location in vehicle. You must have some electronic knowledges and equipment, like soldering iron, hot air gun, multimeter etc. Last step is to solder back memory device, reassemble immobox/BSI/UCH and fit back to car. Depending of vehicle memory device can be serial eeprom, Motorola MCU, Microchip PIC MCU, ST10F269 MCU, Texas Instruments MCU etc… Next step is to program transponder. In order to program transponder you have to remove immobox/BSI/UCH unit from car, open it, desolder memory device or solder wires on testpoints, and read it.
#YOUR NAME ENGLISH DUB WITH SUBTITLES HOW TO#
You must have electronic knowledges and to know how to use soldering-desoldering tools and memory devices programmers.It is your choice what programmer you will use for reading memory devices – TMPro2 memory device programmer or other progarmmer. TMPro2 works with immobilisers eeprom dumps.
#YOUR NAME ENGLISH DUB WITH SUBTITLES CODE#
TMPro 2 Original Transponder Key Programmer Transponder Key Copier And PIN Code Calculator Basic TMPro 2 Original Transponder Key Programmer Transponder Key Copier And PIN Code Calculator Basic